Chopper Pump

Chopper pump —
chips and coolant in one go

Suction, chopping and transfer with a single pump. It breaks up chip-and-coolant mixtures from machine tools and sends them on to filters and separators.

30 mmMax. chip size passed
800 mmMax. immersion depth
30%Air content handled
0Seal maintenance (seal-less)
01 PROBLEM

Sound familiar?

Chips produced during machining are the biggest headache in a coolant circulation line.

Clogged filters and pipes

Long curled chips block or damage filters and pipes and stop the line.

Separate shredder needed

A separate chip shredder adds floor space and cost.

Foamy coolant

Coolant mixed with air is transferred poorly by ordinary pumps.

Frequent maintenance

Seal wear and leaks increase maintenance time.


The Nano Eco chopper pump solves all four with a single pump.
02 HOW IT WORKS

One step: suction ¡æ chop ¡æ transfer

A pump that sends heavily contaminated chip-and-coolant mixtures to filters or separators.

SuctionDraws in coolant and chips together. Immersion installation down to 800 mm.
ChopA cutter at the inlet cuts long chips, passing chips up to 30 mm.
TransferSends chopped chips and coolant to the filter or separator; clean coolant returns to the machine.
03 BENEFITS

Key advantages

Compact, space-saving design

Mounts directly on the tank — no room needed for a separate shredder.

Seal-less design

No shaft seal, so no leaks or seal replacements.

Chops many materials

Easily chops steel, cast iron, aluminum and other chips.

Robust and reliable

Durable materials for long continuous operation.

Fast payback

Savings on shredders and maintenance pay back quickly.

4-pole motor option

Available for sites that need low-speed, quiet operation.

04 APPLICATIONS

Where it is used

Any industrial site handling fluids mixed with chips, sludge or debris. Typical duty: chip transfer and chopping, simultaneous suction and chopping of coolant and chips.


Extended applications

Anywhere fibers, lumps or rag-like debris clog ordinary pumps.

Sewage & wastewater

  • Sumps and lift stations: stops wipes and plastic wrapping around impellers
  • Scum transfer at treatment plants
  • Septage receiving tanks

Livestock & biogas

  • Transfer and mixing of manure with straw or sawdust
  • Feed slurry preparation for digesters
  • Crop residues such as corn stalks and hay

Food, meat & seafood processing

  • Slaughterhouses and poultry: wastewater with feathers and fat
  • Seafood: bones, skins and saline wastewater
  • Fruit, vegetables and bakery: pulp and dough residue

Paper, textiles & recycling

  • Pulp and paper: process water with fibers and wood chips
  • Textiles and laundries: threads, fabric scraps and lint
  • Plastic recycling wash lines: flakes and labels
05 LINEUP

Three impeller types

Choose by chip type and coolant condition. Bore sizes 40A / 50A.

NS 40 ¡¤ 50 — Semi-open impeller. For foamy coolant and ordinary chips; balances efficiency and chip handling
NS 40 ¡¤ 50 — Semi-open impeller. For foamy coolant and ordinary chips; balances efficiency and chip handling
NV 40 ¡¤ 50 — Vortex impeller. Clog-resistant; for long chips and stringy debris
NV 40 ¡¤ 50 — Vortex impeller. Clog-resistant; for long chips and stringy debris
NSV 40 ¡¤ 50 — Pump with cutter. Chops long chips at the inlet; replaces a separate shredder
NSV 40 ¡¤ 50 — Pump with cutter. Chops long chips at the inlet; replaces a separate shredder

ItemSemi-open (NS)Vortex (NV)With cutter (NSV)
PrincipleOpen vanes push the fluid directlyRecessed impeller creates a vortex that carries the fluidInlet cutter cuts chips, then pumps
Hydraulic efficiency¡Ü¡Ü¡Ü¡Ü¡Û¡Û¡Ü¡Ü¡Û
Clog resistance¡Ü¡Ü¡Û¡Ü¡Ü¡Ü¡Ü¡Ü¡Ü
Long chips¡Ü¡Û¡Û¡Ü¡Ü¡Û¡Ü¡Ü¡Ü
Best forFoamy coolant, short chipsStringy debris, intermittent dutyLong aluminum or steel chips; shredder replacement

Comparison based on general pump engineering (¡Ü¡Ü¡Ü excellent / ¡Ü¡Û¡Û fair). In a like-for-like example a vortex pump is less efficient than a standard non-clog pump (48% vs 70%), but because it almost never clogs, total cost of ownership can be lower where run times are short or clog maintenance is frequent.

06 SPEC

Handling capacity by impeller

NS handles foamy coolant; NV 50 handles long, large chips.

ModelAir content (%)Particle size (mm)Chip length (mm)Chip weight (g/L)
NS 403020405
NS 503020407
NV 401015402
NV 501030705

The NSV (with cutter) chops chips at the inlet, so chip-length limits are relaxed. Contact us for details.

07 MODEL

Model code and materials

Example: NS 40 C = semi-open impeller ¡¤ 40A bore ¡¤ C material. 40A covers 2.2–3.0 kW and 50A covers 4.0–5.5 kW.

C Type

Economy

Casing and impeller STS304, other parts SS275 structural steel. For: ordinary water-soluble coolant

S Type

Corrosion-resistant

All wetted parts STS304 / SCS13. For: coolant and washing fluids with corrosion risk

L Type

High corrosion resistance

All wetted parts STS316L / SCS16. For: chloride-bearing, highly corrosive fluids

SCS13 and SCS16 are JIS G5121 cast steel grades corresponding to cast 304 and 316L (ASTM CF8 and CF3M). 316L-type alloys contain molybdenum, which resists pitting corrosion in chloride environments.

08 PERFORMANCE

Performance curves (flow vs. head)

Moving right along the curve, flow increases and head (lifting height) decreases.

NS-40 2.2 kW / 3.0 kW — max. head approx. 15 m ¡¤ max. flow approx. 480 L/min
NS-40 2.2 kW / 3.0 kW — max. head approx. 15 m ¡¤ max. flow approx. 480 L/min
NS-50 4.0 kW / 5.5 kW — max. head approx. 29 m ¡¤ max. flow approx. 830 L/min
NS-50 4.0 kW / 5.5 kW — max. head approx. 29 m ¡¤ max. flow approx. 830 L/min

Values are approximate readings from the curves. Select an operating point to the right of the minimum-flow line.

09 MOTOR

Motors and energy efficiency

Minimum efficiency by class for 4-pole 50 Hz motors under IEC 60034-30-1. Higher-efficiency motors mean lower electricity bills.

Motor outputIE2IE3IE4
2.2 kW84.3%86.7%89.5%
3.0 kW85.5%87.7%90.4%
4.0 kW86.6%88.6%91.1%
5.5 kW87.7%89.6%91.9%

For continuous duty, choosing IE3 or higher gives large running-cost savings. A 4-pole motor turns more slowly at the same output, which helps reduce noise and wear. Source: ABB Technical note, IEC 60034-30-1 (2014).

10 RECOMMEND

Recommended specifications by site

Vertical immersion type (up to 800 mm), 2.2–5.5 kW — suited to small and mid-size tanks and sumps rather than large sewage plants.

SiteModelMaterial
Food and bakery wastewater sumpNSVS Type
Seafood processing (saline)NSVL Type
Small livestock manure pitNSVC ¡¤ S Type
Laundry and textile wastewaterNV ¡¤ NSVC Type
Plastic recycling wash waterNVC Type
Glass and paint sludge pitNS ¡¤ NVS Type
Fish-farm tank dischargeNVL Type

Recommendations are preliminary, based on industry characteristics. For fiber-heavy sites, confirm with an on-site trial before selection. Overseas references (UK food plants): dessert maker 5.5 kW ¡¿ 2; ready-meal maker 18.5 kW ¡¿ 4 (replaced another brand¡¯s pumps after frequent clogging).


One pump, chopping included

Tell us the chip material and length, coolant type and required flow, and we will recommend the right model.

Ask about a model